Driveway Gates | Missouri Raccoon Deer & Tree Theme

Driveway Gates installed at Missouri Farm by JDR Metal Art

20′ Wide Dual Swing Driveway Gates with Custom Tree, Racoon, Whitetail Buck and Grass

Here is 20′ dual swing driveway gate design JDR Metal Art created for a coon hunter’s farm entrance near St. Louis, Missouri.

These gates include many plasma cut steel features including an ornamental tree with oak leaves. Each gate panel is arched from 5′ tall on the ends to 8′ tall in the center!

Creative tree themed driveway gates for Missouri entrance.

Custom Designed Plasma Cut Gate Panels

We create driveway gate designs for our customers. Our designs are crafted to appeal specifically to the customer’s life interests.

For this steel farm gate design we are working with a customer who is a well-known coon dog trainer and breeder. We tailored the metal gate design for him to depict plasma cut silhouettes of trees, deer, raccoons and grass that would complement his farm theme.

Ex. 12' wide x 6' tall
Ex.: Farm, Ranch, Residential, Simple, Traditional, Wildlife, Pets, Equine, Trees, , etc.

 

Kansas City Equine Themed Ranch Driveway Gates by JDR Metal Art

Driveway Gates for Horse Ranch in Kansas City, MO

Driveway gate with horse design.

Here we have a set of horse themed Kansas City driveway gates which was designed for a 14′ entrance and custom built by JDR Metal Art. This project was turned around in about 2 weeks from the time of deposit until we shipped it from our Columbus, Ohio facility.

Custom Made in the USA

We used all US made steel for the frame and silhouettes with 1/8″ thick steel sheet for the horse and fence silhouettes. The gate frames are mixture of square tubing in 1/8″-1/4″ wall thickness (the thicker tubing being for the hinge side of the gate frames). The entry gate posts are 4″ square tubing steel with 1/4″ wall thickness and the hinge sockets are welded to them and include grease fittings and stainless steel ball bearings for a super-smooth swing.The arches were bent with a hand roller and the gate silhouettes were cut by hand with a plasma cutter.

Powder Coated Tough

The gates and posts were pretreated with an eco-friendly rust preventive and bonding promoter (Picklex) and then electrostatically coated with two passes of 60% gloss black super durable grade powder coat baked to a finish at 400 degrees in our in-house powder coat oven. Then we packed them up on a crate with plenty of foam and cardboard to protect the beautiful powder coat finish during transit to their final destination at a Kansas City residence.

Horse Themed Gates:

Entry gate with metal art horses. Drive gate featuring metal horse silhouettes. Metal art dual swing driveway gate with equine theme.

Get a Custom Designed Entrance Gate by JDR Metal Art

We can design a new gate for your driveway entrance. Our gate design process is very reasonably priced. Let us know when you’re ready to get started on your new driveway gate with a theme designed especially for you by JDR Metal Art!

To contact JDR Metal Art:

Ex. 12' wide x 6' tall
Ex.: Farm, Ranch, Residential, Simple, Traditional, Wildlife, Pets, Equine, Trees, , etc.

Missouri Driveway Gates | Artistic Oak Tree & Horse Metal Art

Missouri Driveway Gate

Metal Art Oak Tree Gate with Horse Cutouts Delivered to Missouri

Missouri oak tree drive entrance gate featuring horses by JDR Metal Art

We completed this JDR Metal Art Missouri driveway gate in the summer of 2014.

It is a plasma cut driveway gate we custom designed, built and delivered from our gate shop in Columbus, Ohio to Missouri. It is 15′ long and approximately 8′ tall in the center. Our clients graciously sent us the picture after we installed the gate and their brick columns and concrete driveway were later completed, complementing their new 16′ single swing oak tree gate.

Another picture immediately after fabrication & powder coating…

Missouri driveway gate with plasma cut tree and horse design made into metal art.

This was the longest single piece gate we had built up to that time (until the next Missouri driveway gate we designed and built). Usually we end up splitting the gate into two pieces. This was a setup where fabricating a large single swing gate did not present an issue. We used all 1/8″ thick steel wall tubing for the framework. The oak tree silhouette itself was plasma cut by hand out of a 3/16″ thick sheet of steel. The two metal art horses which accent the tree are also plasma cut from 3/16″ sheet metal. After we put the oak tree leaves on the gate we then sandblasted everything, pretreated it and baked on two coats of “Super Durable” exterior grade black powder coat.

Plasma Cut Tree Headboard

For these particular clients we also built a custom metal art headboard to match a Cali-King size bed frame. It was powder coated with a special order grey metallic flake finish.

Headboard featuring plasma cut metal art tree design

 

 Close-up After Powder Coating:

Grey metallic powder flake on metal art headboard.

Be sure to check out some of our other custom tree themed driveway entry gates. We build many other designs also. You can have us custom design a project specific to your needs. Feel free to contact us with any questions, we would love to help.

Thanks for reading another post on our JDR Metal Art Blog!

Contact JDR Metal Art to learn more:

Ex. 12' wide x 6' tall
Ex.: Farm, Ranch, Residential, Simple, Traditional, Wildlife, Pets, Equine, Trees, , etc.

Custom Wildlife Driveway Gates with Metal Art Deer Scene

Driveway Gates with Wildlife Themes

Metal Art Deer Scene

30′ Automatic Sliding Gate

Shipped to Missouri on 53′ Flatbed

This driveway gate was custom designed for a drive entrance located in Missouri.

The steel wildlife scene is 18′ long and depicts two buck deer, a doe and two fawns on a woodland background. We worked with our clients through their contractor to come up with the gate design.

We also incorporated the street address and family name at the bottom of the gate.

The remaining 12′ of the gate is a frame which will be attached to the automated slide gate opener system.

Missouri wildlife driveway gates featuring deer silhouette plasma cut by JDR Metal Art.

The driveway gate silhouette was both drawn and cut entirely by hand with the help of a plasma cutter.

We used a 3/16″ thick plate of steel for the canvas and 2.5″ square tubing for the frame. The top is arched to accommodate the tree line.

We applied Picklex as a metal  pretreatment in order to eliminate surface oxides and condition the metal for maximum bonding and rust protection.

We then sprayed two coats of industrial rust preventive primer (red oxide) followed by two coats of glossy black rust inhibiting finish paint.

Custom Driveway Entry Gate Themes

Here are some of our other wildlife style entrance gates. You can also check out our tree themed gates and our horse themed gates. Feel free to contact us below to discuss the project you have in mind. We design, build, powder coat and ship all of our gates from Columbus, Ohio to Missouri or just about anywhere else people want them. We consistently offer the best value anywhere for custom wildlife themed driveway gates!

To contact JDR Metal Art:

Ex. 12' wide x 6' tall
Ex.: Farm, Ranch, Residential, Simple, Traditional, Wildlife, Pets, Equine, Trees, , etc.